N1mm logger default messages
- N1MM LOGGER DEFAULT MESSAGES INSTALL
- N1MM LOGGER DEFAULT MESSAGES DRIVER
- N1MM LOGGER DEFAULT MESSAGES CODE
- N1MM LOGGER DEFAULT MESSAGES DOWNLOAD
Go back and verify the above settings and make sure your com ports are correct.
If you do, something is not setup correctly.
N1MM LOGGER DEFAULT MESSAGES CODE
Mine is 9600, N, 8, 1, DTR (Pin4)=CW, RTS (pin 7)=PTT, Icom Code (hex)=94, Radio Nr=1, PTT Delay=30 and PTT via Radio Command SSB Mode is checked. a pass message will be sent, in red to get the other operators attention, and a message will. next section to configure N1MM+ Logger for the contest as an IARU HQ station.
N1MM LOGGER DEFAULT MESSAGES INSTALL
Make sure your Com port is setup correctly. Install the package using all the default selections as they are in each of the installer windows that are presented.
The program will generate a file in the directory you specified calledOnce you have told the program where to save the file, hit OK.
N1MM LOGGER DEFAULT MESSAGES DOWNLOAD
Step four, if you don’t already have it, download and install N1MM Logger+. It’s free and you can find it here. I have included a couple of extra settings that will help later on when using PSK31, RTTY (FSK) and CW keying. Set the following menu items under MENU>SET>Connectors. These are the changes, leave everything else to default settings. Step three, turn your radio on and setup the Icom 7300 using the radio’s menu. Do not connect the USB cable until you have downloaded and installed the driver.
N1MM LOGGER DEFAULT MESSAGES DRIVER
Step one, if you haven’t already, download and install the USB driver from Icom for your Icom IC-7300. If you just want to use a USB Cable with HRD and operate some PSK31 or RTTY (AFSK), take a look at this video. I have found this to be the easiest, because later on I added cw keying and RTTY (FSK) to the mix. Use the CI-V for rig control and the USB for the soundcard. One is the USB cable connected to the radios USB port and the other is a CI-V cable connected to the radios CI-V port. Clearing Rttyrite Sections from writelog.Two cables are used in this setup.Now that you have all your RTTY windows configured, let’s create some messages to send during the contest. It’s located in C:\Users\Username\AppData\Roaming\Afreet\Products\GRITTY. I purposely created a Gritty instance in DI1 RX Window 1 to show you that you could have multiple INI files depending on where you activate your receive-only Gritty windows. Therefore the INI file for that particular instance of Gritty is named Config12.ini (DI 1 RX Window 2) as shown highlighted in Figure 5-12. In our example, we activated Gritty as the second receive-only window, or DI1 RX Window 2.
Therefore whenever you create a DI RX Window, a new INI file gets created for that particular instance of Gritty. However, when Gritty is used with N1MM Logger+, there could be several instances of Gritty (remember you can have up to 4 RX DI windows). To find it, search your computer for Gritty.ini. If you run Gritty as a stand-alone program and not within N1MM Logger+, then the INI file is called Gritty.ini. The only way to change the tone pair in Gritty is to edit the INI file. Gritty works straight out of the box unless you run FSK with low tones or a tone pair other than 2125/2295 Hz. Look for the Gritty download link as shown in Figure 5-1.ġ1. Download Gritty from Alex’s Download page at. For the purpose of this tutorial, it is assumed that MMTTY is configured at DI-1, 2Tone is configured as DI1 RX Window 1 and Gritty will be configured as DI1 RX Window 2.ġ. These instructions will walk you through downloading and installing Gritty as well as interfacing Gritty with N1MM Logger+ to be used as a receive-only decoder. For more information on Gritty, visit the Gritty webpage at. For that reason, it has become a popular “receive only” decoder since being incorporated into N1MM Logger+ in 2015. Although Gritty is designed to decode RTTY signals in 3 kHz of bandwidth, it also works well in narrower bandwidths such as those used in RTTY contesting. It is based on the technology developed for the RTTY Skimmer Server project. Gritty is a free RTTY decoding program written by Alex Shovkoplyas, VE3NEA. N1MM Logger+ > Setting up Gritty in a Receive-only Digital Interface window